In this note we are going to analyze a triangle signal using the FFT. Here is the signal.

• The signal has 4000 samples, and the length of the record is 2 milliseconds.  (It goes from -.001 seconds to +.001 seconds.)
• Since the length of the record is 2 milliseconds, if we compute the FFT for the entire record (which we would normally do), then the fundamental frequency in the computed results is going to be 1/.002 = 500 Hz.  We will refer to this as the fundamental frequency of the data record.
• Within the data record is the triangle signal, and it has a period of 1 millisecond, so it has a frequency of 1 KHz.

        Now, the fundamental frequency of the data record is 500 Hz.  You need to be able to get from that to the actual frequency components of the signal.  Here is what you need to use.

• The fundamental frequency of the data record is the reciprocal of the length (in seconds) of the data record.  Since the data record is 2 milliseconds long (i.e. .002 sec), the fundamental frequency of the data record is 500 Hz.
• In Mathcad, the indices start from zero.  So, a_o, is going to be placed in SigFFT₀ in our workspace above.  Here is a short table of frequencies, indices, etc.  In this table, the indices in the FFT array (SigFFT) are the number of the harmonics of the fundamental frequency of the data arecord.

        Now, we can get at the frequencies in the FFT plot.  Notice the following.

• The first "spike" in the FFT plot is at SigFFT₂.  That corresponds to 1000 Hz which is the fundamental of the signal.  It is not the fundamental of the data record.  It is, however, related to the fact that there are exactly two cycles of the signal in the length of the data record.
• The second "spike" in the FFT plot is at SigFFT₆.  That corresponds to 3000 Hz which is the third harmonic of the signal.
• and so on. . .

        Now, we need to address the vertical scale.  First, you should realize that the vertical plot is the absolute value of the c's in the Fourier expansion.  If you need to understand what the c's are, check these links.

• Note on interpreting the c's as the magnitude and phase of the n^th harmonic.
• Note on viewing the c's as the result of a single integration

        The explantion for the seemingly ridiculous value of over 8000 is this:

• The calculation includes a 1/N term.  That is off by a factor of 2, since you want 2/N.  You have to compensate for that.  In a five volt triangle wave with 4000 data points, the first harmonic of the triangle wave should be 8A/(p²) (where A = 5 for our signal).
• That works out to be 4.053.  The value in the Mathcad workspace is - 2.026j.  It's imaginary because it is the coefficient of a sine - returned in the imaginary part of the FFT.  Multiply by 2 and focus on the absolute value, and we have what we want.
• Here are some links to pages with the expressions for the Fourier Series of a triangle wave signal.  That's where we got that amplitude for the first harmonic.
• A page from Wolfram Research (the folks who make Mathematica).  There is a lot of information on this one web page.  You may want to print it out.
• A java-based simulator
• A nice derivation of the coefficients

        From the material above, you should be able to determine the actual Fourier Series components if you have a signal in a file.  You should be able to distinguish between the fundamental frequency of the data record and the fundamental frequency of the signal embedded in the data record - if that signal is periodic.  And, you should be able to determine the frequencies present in the signal, as well as the amplitudes.

        Here is an example of a signal with 2.5 periods in the data record.  In this signal, we only have 2000 points, so we have to factor that in.

Generally, this can only be described as a mess.  There are no clear-cut lines in this FFT spectrum.  However, note the following table.
 

        Now, we can get at the frequencies in the FFT plot.  Notice the following.

• The fundamental frequency of the signal embedded in the data record is 1250 Hz.  That is not a frequency found in the table.  Rather, the harmonics of the fundamental frequency of the data record are 1000 Hz and 1500 Hz, and they appear at harmonics number 2 and number 3.
• The largest spikes appear at harmonic number 2 and number 3.